Fiberglass Chopping Roving for Chopped Strand Mat & FRP Sheets

        Fiberglass Jet Roving for HOBAS Pipes is a 2400 tex stranded untwisted glass fiber reinforcement developed for jetting,centrifugal casting,HOBAS pipe manufacturing,and selected continuous forming processes. The current product family includes J703,J707,J709,and J750 grades,with approximately ±5% linear-density tolerance and application-specific resin compatibility.Designed for stable chopping,controlled strand dispersion,low-static processing,and efficient resin impregnation,this fiberglass roving can be used in corrosion-resistant FRP pipes,storage tanks,boat hulls,sanitary products,and other composite structures requiring reliable fiber distribution during spray or centrifugal manufacturing.For HOBAS pipe manufacturers and FRP processors,the key selection factors are not only nominal tex,but also resin compatibility,jetting behavior,strand stiffness,choppability,wet-out,and suitability for the exact production process.

Fiberglass Jet Roving Specifications

Key Advantages of Fiberglass Jet Roving

1. Designed for HOBAS Pipe Manufacturing

This product family is specifically positioned for HOBAS pipe and related centrifugal casting processes.

During HOBAS pipe production,fiberglass reinforcement must be introduced into the rotating pipe structure in a controlled and repeatable manner.

Important processing characteristics include:

• Stable fiber feeding

• Consistent chopping

• Controlled strand distribution

• Low-static behavior

• Appropriate strand stiffness

• Efficient resin impregnation

• Stable continuous production

These characteristics can influence both manufacturing stability and reinforcement uniformity.

2. 2400 Tex Linear Density

J703,J707,J709,and J750 are currently listed at 2400 tex.

The current linear-density control range is approximately ±5%.

Stable tex can help manufacturers maintain more consistent:

• Glass-fiber input

• Fiber deposition

• Reinforcement content

• Resin demand

• Production rate

• Finished laminate consistency

3. Fluorine-Free & Boron-Free Glass Composition

The product is listed as a fluorine-free and boron-free glass fiber roving.

This provides a clearly defined glass composition for customers who consider raw-material formulation as part of product selection.

Any environmental or compliance claim beyond the stated material composition should be supported by the relevant document or test report.

4. Good Choppability

Jetting and centrifugal casting processes often require the roving to be chopped continuously at production speed.

Stable chopping behavior can help reduce:

• Incomplete cuts

• Long uncut strands

• Excessive loose fibers

• Cutter buildup

• Process interruption

Actual chopping performance also depends on cutter condition,blade pressure,roller setup,and production speed.

5. Good Strand Dispersibility

After chopping,the fiberglass must distribute effectively across the target surface or rotating mold.

Good dispersibility can help reduce local fiber accumulation and improve reinforcement uniformity.

This is particularly important in:

• HOBAS pipe walls

• FRP tanks

• Boat hull structures

• Sanitary composite products

• Continuously formed FRP components

6. Low-Static Processing Characteristics

Static electricity can interfere with high-speed fiber chopping and deposition.

Low-static behavior can help reduce fibers clinging to equipment or clustering during processing.

Actual static performance also depends on:

• Workshop humidity

• Equipment grounding

• Fiber speed

• Environmental conditions

7. Low Fuzz & Stable Roving Handling

Low fuzz can help reduce fiber accumulation around guides,choppers,and feeding equipment.

This can support cleaner and more stable continuous production.

Actual fuzz levels depend on equipment condition,guide wear,tension,and processing settings.

8. Appropriate Strand Stiffness

For jetting applications,the strand must be sufficiently stable during feeding and cutting while still allowing controlled dispersion after chopping.

Appropriate stiffness can support:

• Stable feeding

• Predictable chopping

• Vertical jetting behavior

• Consistent strand placement

9. Efficient Resin Impregnation

The product is designed for suitable resin penetration during composite processing.

Efficient wet-out is important because the resin must penetrate the fiberglass bundles and form a continuous fiber-matrix system.

Actual impregnation depends on:

• Resin viscosity

• Resin temperature

• Fiber content

• Strand length

• Production speed

• Resin chemistry

• Sizing compatibility

10. Suitable for Corrosion-Resistant FRP Products

The product is positioned for FRP structures used in environments where corrosion resistance is important.

Potential applications include:

• Industrial pipes

• Storage tanks

• Marine composite structures

• Sanitary products

• Process equipment

The corrosion resistance of the finished composite depends primarily on the complete laminate system,especially the resin chemistry,glass content,surface protection,and service environment.

The dry fiberglass roving alone should not be treated as determining chemical resistance.

11. Suitable for Multiple Manufacturing Routes

Depending on grade,the product family can be used for:

• HOBAS pipe production

• Jetting

• Centrifugal casting

• Continuous forming

This makes grade selection especially important because not every model is intended for exactly the same process.

Technical Grades of Fiberglass Jet Roving

J703 Fiberglass Roving for HOBAS Pipes

J703 is specifically listed for HOBAS processing.

Linear Density: 2400 tex

Tolerance: ±5%

Applicable Resin: UP / VE / PP as currently listed

Primary Process: HOBAS

The PP resin listing should be technically confirmed before use because it differs from the surrounding thermoset resin information.

J707 Jet & HOBAS Fiberglass Roving

J707 is designed for both jetting and HOBAS applications.

Linear Density: 2400 tex

Tolerance: ±5%

Applicable Resin: UP / VE

Primary Processes: Jet / HOBAS

It can be considered where stable chopping,dispersion,and resin compatibility are required in continuous FRP production.

J709 Jet & HOBAS Fiberglass Roving

J709 is another 2400 tex grade intended for jetting and HOBAS applications.

Linear Density: 2400 tex

Tolerance: ±5%

Applicable Resin: UP / VE

Primary Processes: Jet / HOBAS

The exact processing difference between J707 and J709 should be confirmed from the detailed technical data rather than inferred without supporting test information.

J750 Fiberglass Roving for Continuous Formation

J750 is listed for continuous formation.

Linear Density: 2400 tex

Tolerance: ±5%

Applicable Resin: UP / VE

Primary Process: Continuous Formation

It should be selected when the customer's manufacturing route differs from conventional HOBAS or jetting production.

Fiberglass Roving for HOBAS Pipes

HOBAS pipes are generally produced using centrifugal casting technology with controlled placement of resin,glass reinforcement,and other structural materials inside a rotating mold.

Fiberglass roving used in this process must provide stable chopping and predictable fiber distribution.

Key production considerations include:

• Roving tex

• Chopped strand length

• Fiber deposition rate

• Resin viscosity

• Resin compatibility

• Pipe diameter

• Wall structure

• Rotation speed

• Fiber distribution

• Cure conditions

The final pipe properties depend on the complete engineered pipe system.

Why Fiber Distribution Matters in HOBAS Pipe Production

Uneven fiber distribution can lead to local variation in:

• Reinforcement content

• Wall structure

• Resin-to-glass ratio

• Mechanical properties

• Surface appearance

Consistent jetting and dispersibility are therefore critical for stable centrifugal pipe production.

Fiberglass Roving for Centrifugal Casting

Centrifugal casting uses rotational force to distribute resin and reinforcement inside a cylindrical mold.

The process can be used to manufacture:

• FRP pipes

• Composite cylinders

• Industrial tubes

• Application-specific hollow structures

The fiberglass must be introduced in a controlled manner so that the reinforcement becomes properly distributed within the designed laminate structure.

Jet Roving for FRP Storage Tanks

Jet roving can also be used in selected FRP storage-tank manufacturing processes.

Potential applications include:

• Chemical storage tanks

• Process tanks

• Water-treatment tanks

• Industrial vessels

Tank performance depends heavily on the selected resin system and laminate design.

For aggressive chemical service,the resin supplier's chemical-resistance data and the finished laminate design should be evaluated carefully.

Jet Roving for Boat Hulls

The current product information also lists fiberglass reinforced boat hulls as an application.

Jet roving can support spray or chopped-fiber composite production in selected marine structures.

Potential applications include:

• Boat hull laminates

• Interior marine components

• Deck-related composite structures

• Marine panels

Final marine performance depends on laminate thickness,resin system,glass content,water resistance,and structural design.

Jet Roving for Sanitary Ware

Sanitary composite products are another listed application.

Potential products include:

• Bathtubs

• Shower bases

• Sanitary panels

• Reinforced bathroom components

Good strand distribution and resin impregnation can help maintain more consistent reinforcement within these molded FRP products.

Jet Roving vs. Chopping Roving

Jet roving and chopping roving may appear similar because both are designed to be cut during processing,but their end uses can differ significantly.

Jet roving is typically optimized for spraying,jetting,or centrifugal deposition,while CSM chopping roving is primarily optimized for manufacturing chopped strand mat.

The two should not automatically be treated as interchangeable.

Important differences may include:

• Sizing system

• Strand stiffness

• Strand separation

• Chopping characteristics

• Dispersion

• Resin compatibility

• Finished process requirements

Jet Roving vs. Filament Winding Roving

Jet roving is chopped before or during application.

Filament winding roving remains continuous and is placed onto a rotating mandrel at controlled angles.

Typical jet-roving products include:

• HOBAS pipes

• Spray-up structures

• Tanks

• Hulls

Typical winding-roving products include:

• Pressure vessels

• FRP pipes

• Insulating tubes

• Cylindrical composite structures

The correct roving depends on whether the process requires chopped or continuous fibers.

Jet Roving vs. Assembled Roving for FRP Sheets

The previous J520 assembled roving is primarily designed for continuous FRP sheet production.

This jet-roving family is focused more on HOBAS,jetting,and centrifugal processes.

The key SEO and application distinction is therefore:

J520 → FRP Sheet / Roofing Sheet / Transparent Panel

J703/J707/J709/J750 → HOBAS Pipe / Jetting / Centrifugal Casting / Tanks

UP & VE Resin Compatibility

UP and VE are the main clearly listed thermoset resin systems for this product family.

Unsaturated polyester can be selected for many general FRP applications.

Vinyl ester may be considered for applications requiring different chemical resistance or mechanical performance.

Final selection depends on:

• Chemical environment

• Service temperature

• Mechanical requirement

• Cure system

• Production speed

• Cost

• Finished-product qualification

About the Epoxy & PP Resin Information

The product description refers to epoxy compatibility,but the model table does not list epoxy for J707,J709,or J750.

J703 lists PP,which is different from the surrounding thermoset resin systems.

Because of this inconsistency,the exact resin compatibility should be confirmed at the model level before publishing a formal technical datasheet or accepting a production order.

I would not recommend placing Epoxy Compatible or PP Compatible prominently in the SEO title until the corresponding model information is clarified.

About UL Certification

The current product page states that the roving has passed UL certification and is suitable for double-wall can production.

However,formal B2B compliance communication should ideally include:

• UL file or report number

• Exact product grade

• Certification scope

• Applicable product category

• Current validity

• Tested construction or end-use limitations

Until these documents are confirmed,the safest wording is:

UL-related certification information is available for applicable grades and should be confirmed for the exact product and end-use requirement.

This is more reliable than stating that every J703/J707/J709/J750 shipment is automatically UL certified for every application.

How to Choose Fiberglass Jet Roving

Quality Control

Stable fiberglass jet-roving quality is important for continuous HOBAS and jetting processes.

Important control items include:

• Linear density

• Tex tolerance

• Strand construction

• Roving integrity

• Choppability

• Fiber dispersion

• Static behavior

• Fuzz level

• Strand stiffness

• Resin wet-out

• Unwinding stability

• Package condition

• Batch identification

For pipe,tank,or other structural products,the finished composite should also undergo application-specific inspection and testing.

Packaging & Shipping

Fiberglass jet roving is individually protected with heat-shrink film or PE stretch film to help prevent moisture,dust,and external contamination.

Typical pallet configuration is approximately 48 or 64 spools per pallet,depending on package size and customer requirements.

Custom spool weight and selected single-spool carton packaging can also be evaluated.

The current recommendation is to stack no more than approximately 2 pallets high to reduce package deformation.

Storage Guidelines

Store the product in a dry,well-ventilated,and rain-protected indoor environment.

Recommended storage conditions are approximately:

Temperature: 5°C to 35°C

Relative Humidity: 35%–65% RH

Keep the roving in its original unopened packaging until production.

Protect the material from:

• Direct sunlight

• Heat sources

• Water

• Condensation

• Dust

• Oil

• External contamination

For best processing performance,the current recommendation is to use the product within approximately 12 months from the production date.

Pallets should be stored on a flat,clean,and dry surface,and excessive loading should be avoided.

Frequently Asked Questions About Fiberglass Jet Roving for HOBAS Pipes

1. What is fiberglass jet roving?

Fiberglass jet roving is a continuous glass fiber reinforcement designed to be fed,chopped,and distributed during spray,jetting,or centrifugal composite manufacturing.

2. What is HOBAS pipe roving?

HOBAS pipe roving is fiberglass reinforcement designed for centrifugal pipe production where chopped fibers are introduced into a rotating pipe-forming system.

3. Which grades are currently available?

The current grades are:

J703,J707,J709,and J750.

4. What is the linear density?

All current grades are listed at 2400 tex.

5. What is the linear-density tolerance?

The current specification lists approximately ±5%.

6. Which grades are designed for HOBAS pipes?

J703 is specifically listed for HOBAS.

J707 and J709 are listed for both jetting and HOBAS.

7. What is J750 used for?

J750 is listed primarily for continuous formation.

8. Which resins are compatible with this roving?

UP and VE are the main clearly listed systems.

Additional resin compatibility should be confirmed by exact grade.

9. Can this product be used with epoxy resin?

The product description mentions epoxy compatibility,but the technical grade table does not list epoxy consistently.

Therefore,epoxy compatibility should be confirmed before commercial use.

10. Why does J703 list PP?

The current model table lists PP for J703,but this differs from the surrounding thermoset resin information.

The exact meaning and compatibility should be technically verified before specification.

11. Can this roving be used for FRP storage tanks?

Yes.

Storage tanks are one of the listed application areas.

The finished tank resin system should be selected according to the stored chemical and service environment.

12. Can it be used for boat hulls?

Yes.

Boat hulls and other marine FRP structures are included among the listed applications.

13. Can it be used for sanitary ware?

Yes.

Sanitary composite products are one of the listed application areas.

14. Why is choppability important?

Stable chopping helps maintain controlled strand lengths and reduces fiber buildup or incomplete cutting during continuous production.

15. Why is dispersibility important?

Good dispersibility helps chopped fibers distribute more uniformly across the target laminate or rotating mold.

16. Why is low static important?

Low-static behavior helps reduce fibers clinging to processing equipment or clustering during deposition.

17. Why is low fuzz important?

Low fuzz helps reduce fiber accumulation around guides and chopping equipment and supports cleaner continuous production.

18. Does this fiberglass itself provide corrosion resistance?

The fiberglass contributes reinforcement,but the corrosion resistance of the finished FRP product depends strongly on the resin system,laminate construction,and service environment.

19. Is this product UL certified?

The current product page lists UL certification information.

For formal purchasing or compliance use,the exact grade,UL document,scope,and validity should be confirmed.

20. Can it be used for double-wall tanks or cans?

The current product information refers to suitability for double-wall can production.

The exact UL scope and finished-product requirements should be verified before qualification.

21. Can jet roving replace filament winding roving?

Generally not without validation.

Jet roving is typically chopped,while winding roving remains continuous.

22. Can it replace CSM chopping roving?

Not automatically.

Although both products may be chopped,the sizing,strand stiffness,and downstream process requirements can differ.

23. What does 2400 tex mean?

2400 tex means approximately 2400 grams per 1,000 meters of roving.

Tex represents linear density,not finished composite strength.

24. How should the product be stored?

Recommended storage conditions are approximately 5°C to 35°C and 35%–65% RH in a dry indoor environment.

25. What is the recommended shelf life?

The current recommendation is approximately 12 months from the production date for best processing performance.

26. What information should I provide when requesting a quotation?

Please provide:

• Required model

• HOBAS/jetting/continuous process

• Resin system

• Finished product

• Required quantity

• UL documentation requirement if applicable

• Spool or packaging requirement

• Destination country or port

Why Choose WGSC Composite?

WGSC Composite supplies fiberglass roving,chopped strand mats,fiberglass fabrics,carbon fiber materials,and reinforcement products for industrial composite manufacturing.

The J703,J707,J709,and J750 fiberglass jet-roving series is positioned for HOBAS pipe,jetting,centrifugal casting,and continuous forming applications. The current grades are based on 2400 tex fiberglass roving with approximately ±5% linear-density tolerance and application-specific UP/VE resin compatibility.

For HOBAS pipe manufacturers,FRP tank producers,marine composite manufacturers,and industrial fiberglass processors,we can evaluate roving grade,resin compatibility,chopping performance,packaging,documentation,and application-specific production requirements.

Whether you are sourcing fiberglass roving for HOBAS pipes,2400 tex jet roving,centrifugal casting fiberglass roving,FRP tank fiberglass reinforcement,UP/VE jet roving,or J703/J707/J709 fiberglass roving,we can provide specification and quotation support according to your manufacturing process.

Request a Quote

Looking for fiberglass jet roving for HOBAS pipes,centrifugal casting,FRP tanks,boat hulls,or industrial composite production?

Please send us your:

Roving Grade · Resin System · Manufacturing Process · Finished Product · UL Documentation Requirement · Quantity · Packaging · Destination

Contact WGSC Composite for J703,J707,J709,J750,and application-specific fiberglass jet-roving requirements.